How do I program a WorkRite desk? 

Where is WorkRite located? Where is WorkRite Ergonomics ‘s headquarters? WorkRite Ergonomics is located in Petaluma, California, United States .

What is WorkRite station? Founded in 1991, Workrite Ergonomics is an industry leader in the design, manufacture and distribution of height-adjustable workcenters and ergonomic office accessories, including adjustable keyboard platform systems and flat panel monitor support systems.

How do I reset my WorkRite standing desk? Unplug power cord and check that all cable connections are secure. Then, reset by holding the down arrow button until table reaches lowest height and moves upward slightly. The height will be displayed and the table will now work properly.

How do I unlock my standing desk?

Press and hold the down arrow button (▼) until the table reaches its lowest position. Then, release. Press and hold the button again for 10 seconds. Then, release.

Why is my standing desk not going up?

Common Reasons Why Your Standing Desk Won’t Go Up

The control box cycle may be out. The power cables used to connect the desk may have not been secured. The legs of the standing desk may be uneven. There could be obstructions in the travel path.

How do I reset my adjustable table?

Unplug your desk from the outlet and wait 30 seconds. Then plug your desk back in. You should hear a few clicks. Press and hold the down button of your desk until the desk reaches its lowest point.

How do I reset my autonomous desk?

Reset Steps:
  1. Unplug the desk for 20 seconds. Plug it back in. Wait a full 20 seconds.
  2. Press the up and down buttons until the desk lowers all the way and beeps or 20 seconds pass.
  3. Release both buttons.
  4. Press the down buttons until the desk beeps one more time or 20 seconds pass.

How do you reset a standing desk ASR?

Reset ASR Error On Electric Standing Desks
  1. Hold the DOWN button for about 3 seconds and then release it.
  2. The electric desk will lower down on its own and returns to a height.
  3. The ASR error will disappear on the LED panel display.

Why is only one side of my standing desk working?

Why only one side of my SmartDesk is raising? First, please check to see if the desk is connected to power, if the control box is still working, if the keypad is receiving power, and if the leg cables are not loosened. The working control box shows a green light if connected to power properly.

What does ASR mean on a standing desk?

This code means the desk needs to be reset. Please take use the following instructions described below when the LED display shows ASR. Please press AND CONTINUE TO HOLD the “▼” button until the desk reaches its lowest height and rebounds to stop to reset.

How do you recalibrate a standing desk?

What does E08 mean on standing desk?

E08 Error Code on Advanced Keypads. Control Box Overheated (H01 Error Code on Advanced Keypads)

What does ASF mean on standing desk?

Keypad displays Error Code ASF or RST

This code is indicating that the desk requires a reset. Try the basic/quick reset procedure described above, this will usually fix the issue.

How do I fix error code E08?

How to Diagnose and Fix Fault Code E08
  1. Switch off and unplug your machine.
  2. Check the motor speed sensor.
  3. Check the wiring and connections to the speed sensor.
  4. If the motor is not turning check the motor itself.

How do I fix E08 error on my desk?

How do I fix my adjustable desk?

What does loc mean on desk?

If “LOC” is displayed, the keypad is locked. Hold “M” until the display switches to display the height.

What does E04 mean on standing desk?

The error codes from E01-E04 are usually issues involving supply of power to the control box or an internal fault with the programming inside. Please unplug the control box for 10-20 minutes and then plug back. Perform the Reset Procedure and check for functionality afterwards.

What does E01 mean on standing desk?

Initialize Your Desk. The desk cannot drive up if it has not been initialized. If the control switch has a digital display that says error code E01, the desk must be initialized.

What does E3 mean on Tresanti desk?

Display indicates E3. The motor is not powered. Unplug the unit and visually inspect whether there are any loose electrical connections between the power cord and the adaptor, or. from the adaptor to the motor. Unplug the power cord for 5 minutes and then plug in again.

By